Hummer H2 Compressor air supply system air suspension

Hummer H2 Compressor air supply system air suspension

SKU: LV00-218A-DUNL
Manufacturer: Dunlop
Origin: Made in UK
Category: Air Supply / Compressors

Dunlop 00218A air supply unit including operating relay

1.648,90 €

incl. 19% VAT , free shipping to Germany (Paket)

MSRP: 3.000,00 €

(Save 45.04%, i.e. 1.351,10 €)

Choose tax zone / country of delivery

TecDoc Catalog

Available from: 31.03.2023

Original OEM DUNLOP dual compressor unit for air suspension.

Includes dual compressors, dryer & valve unit. Control unit included.
This unit replaces the old unit with just one compressor.
.
Can be installed in the following vehicles:
Hummer H2 ab 2008
.
Original spare part number:
88982410, 20803372, 20803367
.
CAUTION: The replacement of the relay is mandatory, otherwise the warranty on the compressor is forfeited!
.
Before you buy a compressor please keep in mind that the main reason a compressor fails is because there is a leak in the Air Suspension System causing the compressor to overwork and "Burn Out". The most common cause for a leak in the system is an old leaky air spring bag. Your compressor warranty will be voided if air spring bags have not been recently replaced in your vehicle. We recommend that in order to maintain your Air Suspension System in optimal condition you purchase new air spring bags.
.
Scope of delivery:
-Compressor aggregate / Air Supply Device
-Relay
.
Your advantage:
-OEM Dunlop
-Much cheaper than authorized repair
-Personal advice
-We as German provider have the European returns policy
-We also have a 2 years warranty
-Worldwide express delivery is our standard
-In Europe we have the longest experience with the topic of air suspension for automobiles in the after market.

Placement on Vehicle:	rear axle (center)
Original spare part numbers:	20803367 88982410 20803372
Manufacturer:	Dunlop
Origin:	Made in UK
Item condition:	Neu
Shipping weight:	14,00 kg
Dimensions(LxWxH) ( Length × Width × Height ):	56,00 × 31,00 × 56,80 cm

Before purchasing a compressor, please note the following:
Most common reasons for a defective compressor is a leak in the System and also a defective relay.
An excessive number of switch-on cycles will cause the relay contacts to stick together.
The result is continuous current on the compressor.
The compressor runs continuously without control until it burns out.

Another main reason why the compressor stops working is moisture inside the compressor.
This happens insidiously via leaks such as:
- Porous or damaged air springs or air spring parts (strut)
- Worn seals, defective compressed air connections and chafed compressed air hoses
- Leaking housings in components such as compressors, valves, air springs or struts.

Every air spring system is vulnerable in this way.
Therefore, follow our advice to avoid any further repairs in the near future.

Before a new compressor is installed, all the reasons why it has been damaged must be completely eliminated.

Our technical advise for the air supply device:
1. Change the relay before installing the compressor even if it seems to still work.
This is also a specification by the car manufacturer. Be sure to change the right relays.
Relays look similar, that is why there is a risk to change the wrong relays.
2. Be sure to check whether the system is leakproof after repairing.
The easiest way to do this is to park the vehicle. Wait for the system to automatically re-adjust if your car has this feature.
Then measure the heights from the ground to the lower edge of the fender as exactly as possible and take notes.
On the day after measure these heights again and compare them with the ones before.
Even a small difference will lead to a damaged compressor and damaged valves in the long run.

When driving with a leaking suspension for a long time it needs to be assumed that the compressor is running more often than normal.
The increased number of cycles of powering on and off is likely to already have damaged the compressor.
Depending on the duration of that condition you should change the relay and check the performance of the compressor to be on the safe side.
After the vehicle stood overnight the compressor normally doesn't need to run more than 20 to 30 seconds for the system to be ready to start.

Contact data

Title

First name

Last name

Company - optional

E-Mail

Phone - optional

Question about item

Your question (Please state chassis number)

Spam protection active