OEM Audi Q7 (4L) system including control valve

OEM Audi Q7 (4L) system including control valve

SKU: LV00-3050-Q700
Manufacturer: WABCO / RAPA / Miessler Automotive® - Own product
Origin: Made in Germany
Category: Air Supply / Compressors

Greater delivery as at Audi - Complete air supply system (WABCO Compressor Valve RAPA LF09S) including operating relay

799,00 €

incl. 19% VAT , free shipping to Germany (Paket)

MSRP: 2.781,00 €

(Save 71.27%, i.e. 1.982,00 €)

Choose tax zone / country of delivery

TecDoc Catalog

Available from: 31.03.2023

This system is prepared for easy installation.
With this offer you get a complete air supply system including control valve.
Exclusive worldwide only available here.

In addition, you receive the following items:
7L0698014 valve control unit (Made in Germany) OE = 611 EURO
7L0616703 Air line - compressed air line between compressor and valve, OE = 70 EURO
7L0616758 Connector - pressure hose / valve, OE = 20 EURO
4H0951253A Work Relay, OE = 16 EURO

Delivery with OEM compressor from WABCO.
The same compressor installed in your vehicle.

For your vehicle model, the original compressor is not offered individually by the vehicle manufacturer.

Can be installed in the following vehicles:
Audi Q7 (4L) 2005 - 2015

Original spare part number:
4L0698007C, 4L0698007, 4L0698007A, 4L0698007B,
7L8616006A, 7L8616006, 7L8616006C,
7L8616007A, 7L8616007, 7L8616007C, 7L8616007E, 7L8616007F,
7L0698853A

Scope of delivery:
Original scope of delivery plus ORIGINAL control valve - OEM WABCO Compressor
Relay

CAUTION: The replacement of the relay is mandatory, otherwise the warranty on the compressor is forfeited!
Relay must be replaced at the same time as the compressor change

Before purchasing a compressor, please note the following:
The most common reason for a defective compressor is a leak in the system, causing the compressor to run too long and too often.
An excessive number of switch-on cycles will cause the relay contacts to stick together.
As a result, the relay no longer functions.
The result is continuous current on the compressor.
The compressor runs continuously without control until it burns out.
Before a new compressor is installed, all the reasons why it has been damaged must be completely eliminated.

To the leak:
A leak can occur in many places, for example:
- Porous or damaged air springs or air spring parts (strut)
- Worn seals, defective compressed air connections and chafed compressed air hoses
- Leaky housings in components such as compressors, valves, air springs or suspension struts.

Every air spring system is vulnerable in this way.
Therefore, follow our advice to avoid any further repairs in the near future.

Basic advantages why you are in good hands with Miessler Automotive® when it comes to air suspension:
- We have been dealing with this topic since 2003
- Manufacturer selected by us is one of the supporting pillars for best quality
- Close cooperation with manufacturers in the field of quality management
- More and more own products that facilitate the repair of your vehicle
- Repair service in our own specialist car workshop.

Our technical advice for the air supply device:
1. Change the relays before installing the compressor even if it seems to still work.
This is also a specification by the car manufacturer. Be sure to change the right relays.
Relays look similar, that is why there is a risk to change the wrong relays.
2. Be sure to check whether the system is leakproof after repairing.
The easiest way to do this is to park the vehicle. Wait for the system to automatically re-adjust if your car has this feature.
Then measure the heights from the ground to the lower edge of the fender as exactly as possible and take notes.
On the day after measure these heights again and compare them with the ones before. Even a small difference will lead to a damaged compressor and damaged valves in the long run.

When driving with a leaking suspension for a long time it needs to be assumed that the compressor is running more often than normal. The increased number of cycles of powering on and off is likely to already have damaged the compressor. Depending on the duration of that condition you should change the relays and check the performance of the compressor to be on the safe side. After the vehicle stood overnight the compressor normally doesn't need to run more than 20 to 30 seconds for the system to be ready to start.

Placement on Vehicle:	middle right outside
Type:	Kompressor
Original spare part numbers:	4L0698007B 7L8616006A 7L8616006 7L8616006C 7L8616007A 7L8616007 7L8616007C 7L8616007E 4L0698007C 7L8616007F 4L0698007 7L0698853A 4L0698007A 7L0698014C
WABCO-OES:	4154031230 415.403.123.0
WABCO-OEM:	415.403.305.0 4154033050
WABCO-GTIN:	4057875156765
Manufacturer:	WABCO / RAPA / Miessler Automotive® - Own product
Origin:	Made in Germany
Features:	100% Passgenauigkeit
Item condition:	Neu
Shipping weight:	7,00 kg
Dimensions(LxWxH) ( Length × Width × Height ):	51,00 × 32,00 × 22,00 cm

Before purchasing a compressor, please note the following:
Most common reasons for a defective compressor is a leak in the System and also a defective relay.
An excessive number of switch-on cycles will cause the relay contacts to stick together.
The result is continuous current on the compressor.
The compressor runs continuously without control until it burns out.

Another main reason why the compressor stops working is moisture inside the compressor.
This happens insidiously via leaks such as:
- Porous or damaged air springs or air spring parts (strut)
- Worn seals, defective compressed air connections and chafed compressed air hoses
- Leaking housings in components such as compressors, valves, air springs or struts.

Every air spring system is vulnerable in this way.
Therefore, follow our advice to avoid any further repairs in the near future.

Before a new compressor is installed, all the reasons why it has been damaged must be completely eliminated.

Our technical advise for the air supply device:
1. Change the relay before installing the compressor even if it seems to still work.
This is also a specification by the car manufacturer. Be sure to change the right relays.
Relays look similar, that is why there is a risk to change the wrong relays.
2. Be sure to check whether the system is leakproof after repairing.
The easiest way to do this is to park the vehicle. Wait for the system to automatically re-adjust if your car has this feature.
Then measure the heights from the ground to the lower edge of the fender as exactly as possible and take notes.
On the day after measure these heights again and compare them with the ones before.
Even a small difference will lead to a damaged compressor and damaged valves in the long run.

When driving with a leaking suspension for a long time it needs to be assumed that the compressor is running more often than normal.
The increased number of cycles of powering on and off is likely to already have damaged the compressor.
Depending on the duration of that condition you should change the relay and check the performance of the compressor to be on the safe side.
After the vehicle stood overnight the compressor normally doesn't need to run more than 20 to 30 seconds for the system to be ready to start.

Contact data

Title

First name

Last name

Company - optional

E-Mail

Phone - optional

Question about item

Your question (Please state chassis number)

Spam protection active