OEM Audi Q7 4L compressor air suspension

Vehicle models

Audi Q7 (4L) 2005-2016

OEM Audi Q7 4L compressor air suspension

SKU: K004-3050-Q700
Manufacturer: ZF WABCO
Origin: Made in Germany
Category: Air Supply / Compressors

OEM WABCO 4154033050 compressor including relay / closer for the compressor circuit

499,00 €

incl. 19% VAT , free shipping to Germany (Paket)

MSRP: 1.862,35 €

(Save 73.21%, i.e. 1.363,35 €)

Choose tax zone / country of delivery

Available immediately
Delivery time: 1 - 2 Workdays (DE - int. shipments may differ)

TecDoc Catalog

Item

This is the original compressor from the same supplier to the car manufacturer.
This means that this compressor comes from the same production line and undergoes the same quality controls - official aftermarket product from `WABCO Direct`.
There is no difference to the original version.
Replace the supplied working relay. This is also an absolute requirement of the car manufacturer.
The included suspension elements for the compressor prevent increased vibration noise.

Original WABCO replacement:
4154033020; 415 403 302 0

We would like to point out at this point that the original spare part numbers mentioned refer to the complete air supply system, as this product is not offered separately by the car manufacturer. Therefore, there is no original spare part number for the scope of delivery offered by us.
If you are not familiar with the topic of air suspension, this can lead to additional work and possible complications that could not have been foreseen beforehand.
99% of the compressor offers offered worldwide as aftermarket products consist, as here, only of the compressor itself, ie
- without wiring harness OE: 7L0 971 291 A; 7L0971291A
- without working relay OE: 4H0 951 253 A; 4H0951253A
- without intake rod (not available from VW/AUDI - can be expensive if defective).
- without mounting kit for the compressor OE: 7L0 698 853 A; 7L0698853A; and OE: 7L0698349
- without aluminum holder (not available separately from VW/AUDI)
- without control valve OE: 7L0698014
- without sensor G290 OE: 7L0971291A

We also offer you much more extensive delivery scopes.

We would be happy to make you an offer for diagnosis and installation (repair) in our own car workshop.
Please contact us by clicking on the button: "Question about the product".

Can be installed in the following vehicles:
Audi Q7 4L 2005-2015

Replaces compressors from the air supply system with the original spare part numbers:
4L0698007C, 4L0698007, 4L0698007A, 4L0698007B,
7L8616006A, 7L8616006, 7L8616006C,
7L8616007A, 7L8616007, 7L8616007C, 7L8616007E, 7L8616007F,
7L0698853A

Scope of delivery:
compressor
relay

ATTENTION: Warranty only when using a new relay!

Before purchasing a compressor, please consider the following:
The most common reason for a defective compressor is a leak in the system, causing the compressor to run for too long.
This then leads to a burnout of the device.
A leak can occur in many places, such as:
- Porous or damaged air springs or air spring components (shock absorber)
- Worn seals, defective compressed air connections and frayed compressed air hoses
- Leaky housings of components such as compressor, valves, air springs or suspension struts.
The compressor warranty cannot be honored if a leak persists.

A frayed or porous intake hose / intake rod will destroy the compressor.
A kinked intake hose will cause the compressor to overheat and ultimately be destroyed.
Leaky pipes, pipe connections or air bellows must be repaired, otherwise we cannot provide a guarantee.
We may establish such conditions when making a warranty or guarantee claim.

Your benefits:
- Made in Germany
- Much more cost-effective than an authorized workshop
- Personal advice
- As a German provider, we have the European right of withdrawal
- 2 years warranty
- Worldwide express shipping
- We have the longest experience in Europe with air suspension for automobiles in the aftermarket.

Our technical advice for air supply:
1. Increased running noise of the compressor is often caused by a suspension that is no longer functioning.
Be sure to also change the suspension rubbers and springs.
2. A porous intake hose is often the cause of compressor failure.
Change this and, if possible, the filter/silencer at the same time.
We don’t want the new compressor to fail prematurely for this reason.
3. After the repair, make sure that the system is absolutely leak-proof.
The easiest way to check this is to park the vehicle and wait for the system to automatically adjust if your vehicle has this feature.
Measure and note down all heights that air supports from the ground to the bottom edge of the fender. Check and compare these heights the next day.
Even a small deviation in the distances will cause damage to the compressor and the valves in the long term.

If you have been driving with a leaky chassis for some time, it is likely that the compressor is running more often than normal.
This increased number of on and off cycles may have already damaged the compressor.
Depending on how long this condition has been going on, you should replace the relay as a precaution and check the compressor's performance.
After the car has been standing overnight, a compressor should not run for longer than 20 to 30 seconds until the system is ready to start again.

Placement on Vehicle:	middle right outside
Type:	Compressor
Original spare part numbers:	7L8-616-006-A 7L8-616-006 7L8-616-006-C 7L8-616-007-A 7L8-616-007-7L8-616-007-C 7L8-616-007-E 4L0-698-007-C 7L8-616-007-F 4L0-698-007 7L0-698-853-A 4L0-698-007-A 7L0-698-014-C 4L0-698-007-B
Suitable for original spare part numbers:	7L8616007A 7L8616007 7L8616007C 7L8616007E 4L0698007C 7L8616007F 4L0698007 7L0698853A 4L0698007A 4L0698007B 7L8616006A 7L8616006 7L8616006C
WABCO-OES:	415.403.123.0 4154031230
WABCO-GTIN:	4057875156765
Origin:	Made in Germany
Manufacturer:	ZF WABCO
WABCO-OEM:	415.403.305.0 4154033050
Item condition:	New
Features:	100% Accuracy of Fit
Shipping weight:	5,00 kg

Before purchasing a compressor, please note the following:
Most common reasons for a defective compressor is a leak in the System and also a defective relay.
An excessive number of switch-on cycles will cause the relay contacts to stick together.
The result is continuous current on the compressor.
The compressor runs continuously without control until it burns out.

Another main reason why the compressor stops working is moisture inside the compressor.
This happens insidiously via leaks such as:
- Porous or damaged air springs or air spring parts (strut)
- Worn seals, defective compressed air connections and chafed compressed air hoses
- Leaking housings in components such as compressors, valves, air springs or struts.

Every air spring system is vulnerable in this way.
Therefore, follow our advice to avoid any further repairs in the near future.

Before a new compressor is installed, all the reasons why it has been damaged must be completely eliminated.

Our technical advise for the air supply device:
1. Change the relay before installing the compressor even if it seems to still work.
This is also a specification by the car manufacturer. Be sure to change the right relays.
Relays look similar, that is why there is a risk to change the wrong relays.
2. Be sure to check whether the system is leakproof after repairing.
The easiest way to do this is to park the vehicle. Wait for the system to automatically re-adjust if your car has this feature.
Then measure the heights from the ground to the lower edge of the fender as exactly as possible and take notes.
On the day after measure these heights again and compare them with the ones before.
Even a small difference will lead to a damaged compressor and damaged valves in the long run.

When driving with a leaking suspension for a long time it needs to be assumed that the compressor is running more often than normal.
The increased number of cycles of powering on and off is likely to already have damaged the compressor.
Depending on the duration of that condition you should change the relay and check the performance of the compressor to be on the safe side.
After the vehicle stood overnight the compressor normally doesn't need to run more than 20 to 30 seconds for the system to be ready to start.

Contact data

Title

First name

Last name

Company - optional

E-Mail

Phone - optional

Question about item

Your question (Please state chassis number)

Assembly instructions

Assembly instructions