Audi A6 C7 4G Allroad Quattro compressor air suspension 4G0616005D

Audi A6 C7 4G Allroad Quattro compressor air suspension 4G0616005D

SKU: K000-M303-AL4G
Manufacturer: Miessler Automotive® - Own product
Origin: ISO / IATF certified manufacturer
Category: Air Supply / Compressors

Compressor including fasteners, compressed air hose, hose connector and working relay

383,91 €

incl. 19% VAT , free shipping to Germany (Paket)

MSRP: 1.220,00 €

(Save 68.53%, i.e. 836,09 €)

Choose tax zone / country of delivery

Available immediately
Delivery time: 1 - 2 Workdays (DE - int. shipments may differ)

TecDoc Catalog

Item

This compressor 4G0616005D for the Audi A6 C7 4G Allroad Quattro is characterized by the highest quality standard (manufacturer quality management IATF-16949) and additional scope of delivery.

You will also receive the wearing parts from the fastening kit to avoid vibration noises and the pre-assembled compressed air hose.

We would be happy to make you an offer for diagnosis and installation (repair) in our own vehicle workshop.
Please contact us by clicking on the button: “Question about the product”.

Can be installed in the following vehicles:
Audi A6 C7 4G Allroad Quattro (2012-2018)

Replaces compressors with the original spare part numbers:
4G0 616 005 C ; 4G0616005C
4G0 616 005 D ; 4G0616005D

Scope of delivery:
Air suspension compressor - Miessler Automotive®
Relay (4H0951253)
Wear parts from fastening kit (4H0698505)
Repair kit pressure pipe compressor (4G0698306)

ATTENTION: Warranty only applies if a new relay is used!

Before purchasing a compressor, please consider the following:
The most common reason for a faulty compressor is a leak in the system, causing the compressor to run for too long.
This then leads to a burnout of the device.
A leak can occur in many places, such as:
- Porous or damaged air springs or air spring components (suspension strut)
- Worn seals, defective compressed air connections and chafed compressed air hoses
- Leaky housings in components such as compressors, valves, air springs or suspension struts.
The compressor warranty cannot be guaranteed if a leak persists.

Your advantages:
- Documented quality assurance (Quality management in the automotive industry IATF-16949)
-Much cheaper than an authorized workshop
-Personal advice
-We as a German provider have the European right of withdrawal
-2 year warranty
-Worldwide express shipping is standard for us
-We have the longest experience in Europe with air suspension for automobiles in the aftermarket.

Our technical advice for air supply:
1. An increased running noise of the compressor is often caused by the suspension of the compressor no longer functioning.
Be sure to also change the suspension rubbers and springs.
2. A porous intake hose is often the cause of compressor failure.
Change this and, ideally, the filter/noise damper at the same time.
We don't want the new compressor to fail prematurely for this reason.
3. Change the working relay before installing the compressor, even if it still appears to be functional.
This is also a mandatory requirement of the car manufacturer.
Make sure you are changing the correct relay. Relays are similar. There is a great risk of replacing the wrong relay.
4. After the repair, make sure that the system is absolutely tight.
The easiest way to determine this is to park the vehicle and wait for the system to automatically adjust (if your vehicle has this feature). Accurately measure and note all heights that are air-assisted, from the ground to the bottom edge of the fender. The next day check and compare these heights.
Even a small deviation in the distances leads to long-term damage to the compressor and the valves.

If you have been driving for some time with a leaky undercarriage, it can be assumed that the compressor is running more often than normal. This increased number of on and off cycles may have already damaged the compressor. Depending on how long this condition has lasted, you should change the relay as a precaution and check the compressor's performance. After the car has been parked overnight, a compressor should not run for more than 20 to 30 seconds until the system is ready to start again.

Placement on Vehicle:	rear axle (center)
Type:	Compressor
Original spare part numbers:	4G0-616-005-B 4G0-616-005-O 4G0616005O 4G0-616-005-Z 4G0616005Z 4G0-616-005-A 4G0-616-005-P 4G0616005P 4G0-616-005-E 4G0616005E 4G0-616-005-Q 4G0616005Q 4G0-616-005-F 4G0616005F 4G0-616-005-R 4G0616005R 4G0-616-005-G 4G0616005G 4G0-616-005-S 4G0616005C 4G0616005S 4G0-616-005-H 4G0616005H 4G0-616-005-T 4G0616005D 4G0616005T 4G0-616-005-C 4G0-616-005-I 4G0616005I 4G0-616-005-U 4G0616005U 4G0-616-005-D 4G0-616-005-J 4G0616005J 4G0-616-005-V 4G0616005V 4G0-616-005 4G0-616-005-K 4G0616005K 4G0-616-005-W 4G0616005W 4G0616005B 4G0-616-005-L 4G0616005L 4G0-616-005-X 4G0616005X 4G0616005A 4G0-616-005-M 4G0616005M 4G0-616-005-Y 4G0616005Y
WABCO-OES:	4154034180 415.403.418.0
Origin:	ISO / IATF certified manufacturer
Manufacturer:	Miessler Automotive® - Own product
WABCO-OEM:	4154039692 415.403.969.2
Item condition:	New
Features:	100% Accuracy of Fit
Shipping weight:	5,00 kg

Before purchasing a compressor, please note the following:
Most common reasons for a defective compressor is a leak in the System and also a defective relay.
An excessive number of switch-on cycles will cause the relay contacts to stick together.
The result is continuous current on the compressor.
The compressor runs continuously without control until it burns out.

Another main reason why the compressor stops working is moisture inside the compressor.
This happens insidiously via leaks such as:
- Porous or damaged air springs or air spring parts (strut)
- Worn seals, defective compressed air connections and chafed compressed air hoses
- Leaking housings in components such as compressors, valves, air springs or struts.

Every air spring system is vulnerable in this way.
Therefore, follow our advice to avoid any further repairs in the near future.

Before a new compressor is installed, all the reasons why it has been damaged must be completely eliminated.

Our technical advise for the air supply device:
1. Change the relay before installing the compressor even if it seems to still work.
This is also a specification by the car manufacturer. Be sure to change the right relays.
Relays look similar, that is why there is a risk to change the wrong relays.
2. Be sure to check whether the system is leakproof after repairing.
The easiest way to do this is to park the vehicle. Wait for the system to automatically re-adjust if your car has this feature.
Then measure the heights from the ground to the lower edge of the fender as exactly as possible and take notes.
On the day after measure these heights again and compare them with the ones before.
Even a small difference will lead to a damaged compressor and damaged valves in the long run.

When driving with a leaking suspension for a long time it needs to be assumed that the compressor is running more often than normal.
The increased number of cycles of powering on and off is likely to already have damaged the compressor.
Depending on the duration of that condition you should change the relay and check the performance of the compressor to be on the safe side.
After the vehicle stood overnight the compressor normally doesn't need to run more than 20 to 30 seconds for the system to be ready to start.

Contact data

Title

First name

Last name

Company - optional

E-Mail

Phone - optional

Question about item

Your question (Please state chassis number)

Assembly instructions

Assembly instructions