Audi Q7 (4L) system including control valve

Audi Q7 (4L) system including control valve

SKU: LV00-W3OE-Q700
Manufacturer: WABCO / RAPA / Miessler Automotive® - Own product
Origin: Made in Germany
Category: Air Supply / Compressors

Larger scope of delivery than Audi - Complete air supply system (WABCO Provia compressor, RAPA LF09S valve) including relay / closer for the compressor circuit

739,00 €

incl. 19% VAT , free shipping to Germany (Paket)

MSRP: 2.781,00 €

(Save 73.43%, i.e. 2.042,00 €)

Choose tax zone / country of delivery

Available immediately
Delivery time: 1 - 2 Workdays (DE - int. shipments may differ)

TecDoc Catalog

Item

For this system we use the WABCO Provia 415403305R compressor.
With this offer you receive a complete air supply system including control valve.
Exclusively available worldwide only here.

Additionally you will receive the following items:
7L0698014 Valve unit (Made in Germany) OE = 611 EURO
7L0616703 Air line - compressed air line between compressor and valve, OE = 70 EURO
7L0616758 Connector - pressure hose / valve, OE = 20 EURO
4H0951253A Working relay, OE = 16 EURO

The original compressor is not offered separately by the vehicle manufacturer for your vehicle model.

We would be happy to make you an offer for diagnosis and installation (repair) in our own car workshop.
Please contact us by clicking on the button: "Question about the product".

Can be installed in the following vehicles:
Audi Q7 (4L) 2005 - 2015

Replaces compressors with the original spare part numbers:
4L0698007C, 4L0698007, 4L0698007A, 4L0698007B,
7L8616006A, 7L8616006, 7L8616006C,
7L8616007A, 7L8616007, 7L8616007C, 7L8616007E, 7L8616007F,
7L0698853A

Scope of delivery:
Original scope of delivery plus ORIGINAL control valve - WABCO Provia 415403305R compressor
-Including relay

Warranty only when using a new relay!
The relay must be replaced at the same time as the compressor is changed.

Before purchasing a compressor, please consider the following:
The most common reason for a defective compressor is a leak in the system, causing the compressor to run too long and too often.
A disproportionate number of switch-on cycles leads to premature sticking of the relay contacts.
This means the relay no longer functions.
The result is a constant current on the compressor.
The compressor runs continuously without control until it burns out.
Before a new compressor is installed, all reasons why it was damaged must be completely eliminated.

Regarding the leak:
A leak can occur in many places, such as:
- Porous or damaged air springs or air spring components (shock absorber)
- Worn seals, defective compressed air connections and frayed compressed air hoses
- Leaky housings of components such as compressor, valves, air springs or suspension struts.
.
Every air suspension system is vulnerable in this way.
Therefore, follow our advice to avoid having to make further repairs in the near future.

Basic advantages why you are in good hands with Miessler Automotive® when it comes to air suspension:
- We have been dealing with this topic since 2003
- Manufacturers selected by us are one of the pillars for best quality
- Close cooperation with manufacturers in the area of quality management
- More and more own products that make the repair of your vehicle easier
- Repair service in our own specialist workshop

Our technical advice for air supply:
1. Increased running noise of the compressor is often caused by a suspension that is no longer functioning.
Be sure to also change the suspension rubbers and springs.
2. A porous intake hose is often the cause of compressor failure.
Change this and, if possible, the filter/silencer at the same time.
We don’t want the new compressor to fail prematurely for this reason.
3. Replace the operating relay before installing the compressor, even if it still appears to be functional.
This is also a mandatory requirement of the car manufacturer.
Make sure you are changing the correct relay. Relays are similar. There is a high risk of changing the wrong relay.
4. After the repair, make sure that the system is absolutely leak-proof.
The easiest way to determine this is to park the vehicle and wait for the system to automatically adjust (if your vehicle has this feature). Measure and note down all heights that are air-assisted, from the ground to the bottom edge of the fender. Check and compare these heights the next day.
Even a small deviation in the distances will cause damage to the compressor and the valves in the long term.

If you have been driving with a leaky chassis for some time, it is likely that the compressor is running more often than normal. This increased number of on and off cycles may have damaged the compressor. Depending on how long this condition has been going on, you should replace the relay as a precaution and check the compressor's performance. A compressor should not run for longer than 20 to 30 seconds after the car has been standing overnight until the system is ready to start again.

Placement on Vehicle:	middle right outside
Type:	Compressor
Original spare part numbers:	4L0698007B 7L8-616-007-E 4L0-698-007-C 7L8616006A 7L8-616-007-F 4L0-698-007 7L8616006 7L0-698-853-A 4L0-698-007-A 7L8616006C 7L0-698-014-C 4L0-698-007-B 7L8616007A 7L8-616-006-A 7L8616007 7L8-616-006 7L8616007C 7L8-616-006-C 7L8616007E 4L0698007C 7L8-616-007-A 7L8616007F 4L0698007 7L8-616-007-7L0698853A 4L0698007A 7L8-616-007-C 7L0698014C
WABCO-OES:	4154031230 415.403.123.0
WABCO-GTIN:	4057875156765
Origin:	Made in Germany
Manufacturer:	WABCO / RAPA / Miessler Automotive® - Own product
WABCO-OEM:	415.403.305.0 4154033050
Item condition:	New
Features:	100% Accuracy of Fit
Shipping weight:	7,00 kg

Before purchasing a compressor, please note the following:
Most common reasons for a defective compressor is a leak in the System and also a defective relay.
An excessive number of switch-on cycles will cause the relay contacts to stick together.
The result is continuous current on the compressor.
The compressor runs continuously without control until it burns out.

Another main reason why the compressor stops working is moisture inside the compressor.
This happens insidiously via leaks such as:
- Porous or damaged air springs or air spring parts (strut)
- Worn seals, defective compressed air connections and chafed compressed air hoses
- Leaking housings in components such as compressors, valves, air springs or struts.

Every air spring system is vulnerable in this way.
Therefore, follow our advice to avoid any further repairs in the near future.

Before a new compressor is installed, all the reasons why it has been damaged must be completely eliminated.

Our technical advise for the air supply device:
1. Change the relay before installing the compressor even if it seems to still work.
This is also a specification by the car manufacturer. Be sure to change the right relays.
Relays look similar, that is why there is a risk to change the wrong relays.
2. Be sure to check whether the system is leakproof after repairing.
The easiest way to do this is to park the vehicle. Wait for the system to automatically re-adjust if your car has this feature.
Then measure the heights from the ground to the lower edge of the fender as exactly as possible and take notes.
On the day after measure these heights again and compare them with the ones before.
Even a small difference will lead to a damaged compressor and damaged valves in the long run.

When driving with a leaking suspension for a long time it needs to be assumed that the compressor is running more often than normal.
The increased number of cycles of powering on and off is likely to already have damaged the compressor.
Depending on the duration of that condition you should change the relay and check the performance of the compressor to be on the safe side.
After the vehicle stood overnight the compressor normally doesn't need to run more than 20 to 30 seconds for the system to be ready to start.

Contact data

Title

First name

Last name

Company - optional

E-Mail

Phone - optional

Question about item

Your question (Please state chassis number)